What is the Specifications of solar power wireless intelligent traffic signal light controller system ?
Model:NBTSC-200M
1,Solar Traffic Light Controller of Introdution:
Noble's Second Generation Wireless Traffic Light controller,with vehicle loop sensor & pedestrain push button &Greenwave function can for your choice.
Besides, it can controlled by wifi remote control handset on the site or software control in the center room as you wanted. It makes more efficent & easier manage the road traffic safety control.
2. Introduction of Traffic Light Controller:
- Adapts 32 digits ARM CPU
- Modular in design for easy maintenance
- 1 master and 4 slave controller work together by wireless.
- 1%-100% energy saving adjustment, automatic brightness control
- WIFI for handset to remote control the controller.
- 433MHz frequency work for whole system
- 20-32 signal driving outputs.
- Fuse protected driver output PSU with LED indicator.
- 24 -36 Loop Detector inputs(Optional)
- 8 channel at most, the detecting function of wireless pedestrian button.
- Communication:It can connect to traffic signal sites via permanently connected serial links or TCP/IP(Ethernet, Fiber optics on LAN/WLAN) or GPRS
- GPS Real-time clock for wireless sync available(Optional)
- Historical data memory up to ten years
3. Specification of Traffic Light Controller:
A) Remote control over 100 intersection on the center room by the agencies.
B) Vehicle loop detector: It measures traffic volumes and flows at intersections mainly using inductive loop detectors buried in the road surface.
C) Push button: It was used by the road crossing persons.
D) Automatic Master Controllers faulty detecting: Yellow signal flashing on error conditions and direction communication failure etc.
E) Fault detection recored: Error logs sent to traffic monitoring center when networked, Collection and analysis of historical data fast
F) Accessible to emergency state at any time
G) Green Conflict Monitoring
H)Battery voltage monitoring(Solar Power), Low Power Alarm
I) Greenwave function:It operates in real-time, adjusting signal timings throughout the system in response to variation in traffic demand and system capacity.
J) Frequency channel can be setting via DIP switch.
K) Fault diagnose function for open or close.
4. Show of Traffic Light controller ( With Pedestrian Push Button Function)
① Mode number 2-1，the running of vehicle signal light is according to the plan what we set circularly.pedestrian light always is OFF, When someone press the push button, if this direction’s pedestrian green light doesn’t have conflict with other directions’ pedestrian green light, the pedestrian green light will be ON: If this direction’s pedestrian green light has conflict with other directions’ pedestrian green light, then this direction’s pedestrian
light will not be ON soon, however the pedestrian red light will flash until the there is no green conflict, the green light will be ON.
②Mode number 2-2, the vehicle signal light will run according to the plan we set circularly.All the directions’ pedestrian red light will be ON. When someone press push button, if this direction’s pedestrian green light doesn’t have conflict with other direction’s pedestrian green light, the pedestrian green light will be ON. If this direction’s pedestrian green light has conflict with other directions’pedestrian green light, then this direction’s pedestrian light will not be ON soon, the green light will be ON until the there is no green conflict,at same time the pedestrian red light will be OFF.
5. Show of Noble's Traffic Light Controller ( With Vehicle Loop Detector function):
6. Show of Noble's Traffic Light Controller ( With Central control software ):
7,Traffic Controller of Technical Specification:
A:Master controller
| Item: |
NBTSC-200M |
 |
| CPU: |
ARM7,32 bit |
| Power supply: |
220VAC |
| Current: |
200MA |
| Power： |
≦3.5W |
| Working frequency: |
433Mhz |
Wireless communiction
distance: |
<200m |
| Working temperature: |
-20-60℃ |
| Working humidity: |
＜95% |
| IP rate: |
Ip54 |
| Net weight: |
3.7kg |
| Gross weight: |
4.6kg |
B:Slave controller
| Item: |
NBTSC-100S |
 |
| CPU: |
ARM7,32 bit |
| Power supply: |
DC12V |
| Current: |
160MA |
| Power： |
≦3.5W |
| Working frequency: |
433Mhz |
Wireless communiction
distance: |
<200m |
| Working temperature: |
-20-60℃ |
| Working humidity: |
＜95% |
| IP rate: |
Ip54 |
| Net weight: |
2.4kg |
| Gross weight: |
3.4kg |
| Carton size: |
4000*2800*1850mm |
C:Handheld
| Item: |
NBHH-50 |
 |
| Power supply: |
DC3.7V |
| Battery |
5000mAH |
| Current： |
100mA |
| Power： |
0.4W |
| Working frequency: |
433Mhz |
| Working time： |
3-5days |
| Communiction Distance： |
≦20M |
| Charge method： |
USB(mini 2.0USB, read time<1s ) |
| Method： |
WIFI(communication
distance<20m) |
| Working temperature: |
-
20℃-60℃ |
| Working humidity: |
＜95% |
| IP rate: |
Ip54 |
| Net weight |
0.5KG |
Here are traffic light controller sales:
2nd Main Power Intelligent Traffic Light Controller
solar powered traffic system
GPS synch roadsigns system
Arrow board system
parking guidance system
